Please see the instructions below for more information:
Step 1
Press button A and enter pincode.
Step 2
Then button A followed by the number 2 this disables the tamper on the siren for one hour and will give a beep to notify that it’s been disabled. Then remove the batteries and this will remove the device from the system.
Step 3
To reenable the tamper press button A followed by the pincode.
Step 4
Then button A followed by number 3 and you should hear a beep on the siren.
I am installing my Yale siren-based alarm, but I can’t disable the siren tamper. Why is this?
Your Key Pad may not be programmed in correctly to the siren. In order to programme the keypad into the siren, the siren will need to be reset. Please see the steps below for more information and instructions:
Step 1
Remove the front cover of the siren and turn it to off using the on/off switch.
Step 2
Press the learn button twice to remove the residual power.
Step 3
Then move switch 1 and 4 to the ON position.
Step 4
Then turn the power on and it will beep and flash.
Step 5
Switch 1,2 ,3 - to the OFF position. Switch 4 - to the ON position.
Step 6
To reprogram the keypad press the learn button on the siren for 1 second and you will get a beep and a flash.
Step 7
Press all the learn buttons on all the devices once to learn them back in again and you will hear a beep every time they are learnt back in.
Step 8
To learn the keypad back in press button A and add pincode.
Step 9
Then button A and the number 8.
Step 10
Then button A and number 1, then press disarm twice and press the learn button on the siren. Now disable the tamper then fit the siren back on the wall .
There are no lights on my Door Contact / Keypad after I have changed the batteries
Please ensure the battery is inserted in the correct manner, see the picture below.
Step 1
Go into your programme menu (blue menu button, then enter your pin code followed by the tick key), to prevent an alarm activation. Then continue to change the batteries.
What positions do the DIP switches need to be?
1,2,3 – OFF
4 – ON
Step 1
Locate the dip switches on the back of the alarm.
Step 2
Switch 1,2 ,3 - to the OFF position. Switch 4 - to the ON position.
How do I add devices to my HSA 6200 alarm?
See images below for instructions:
Step 1
Press button A followed by pincode.
Step 2
Then button A followed by number 2.
Step 3
Press button A and then number 4 and the siren will beep and flash at this point. Now you can press the button on the device you want to add and the siren will beep and flash.
Step 4
Then press button A and the number 5.
Step 5
Now press button A and the number 3. Then press disarm twice.
How do I change the batteries on my HSA 6200 alarm?
Disable the siren tamper via the Key Pad.
Step 1
Press button A and enter pincode
Step 2
Then button A followed by the number 2 this disables the tamper on the siren for one hour and will give a beep to notify that it’s been disabled. Open the device and change the batteries. Then to put the tamper back on.
Step 3
Press button A and enter pincode
Step 4
Then button A followed by number 3 and you should hear a beep on the siren.
Can I ‘part arm’ my system, using the HOME button on the keypad?
This feature is not available for this system.
Can I extend my entry and exit time on my HSA 6200 Alarm Kit?
Not on this system. 20 seconds is the default for every device.
Can I have an internal sounder on the HSA 6200 Alarm Kit?
Yes, you can purchase a HSA 6400 panel, as an additional item, to give you this feature.
Troubleshooting
How do I pair my siren to the hub?
To pair the siren to the hub please follow the steps below:
Press and hold the learn button on the hub until the LED flashes.
Make sure dip switches 1 2 3 and 4 on siren are on OFF position , then turn the power switch ON and press the learn button for 1 second.
Go back to the hub and press the learn button for 1 second.
Go to the siren and press the learn button for 1 second.
Press and hold the learn button on the hub until the LED stops flashing.
To test it , you will have to fully arm the system and wait for the countdown to finish. Then trigger the alarm with any door contact set to entry.
I am installing my Yale siren-based alarm, but I can’t disable the siren tamper. Why is this?
Your Key Pad may not be programmed in correctly to the siren. In order to programme the keypad into the siren, the siren will need to be reset. Please see the steps below for more information and instructions:
Step 1
Remove the front cover of the siren and turn it to off using the on/off switch.
Step 2
Press the learn button twice to remove the residual power.
Step 3
Then move switch 1 and 4 to the ON position.
Step 4
Then turn the power on and it will beep and flash.
Step 5
Switch 1,2 ,3 - to the OFF position. Switch 4 - to the ON position.
Step 6
To reprogram the keypad press the learn button on the siren for 1 second and you will get a beep and a flash.
Step 7
Press all the learn buttons on all the devices once to learn them back in again and you will hear a beep every time they are learnt back in.
Step 8
To learn the keypad back in press button A and add pincode.
Step 9
Then button A and the number 8.
Step 10
Then button A and number 1, then press disarm twice and press the learn button on the siren. Now disable the tamper then fit the siren back on the wall .
Why is the LED flashing on my HSA 6200 Key Pad when any key is pressed?
This is because the batteries are low. Please see instructions on how to change the batteries.
Step 1
Press button A and enter pincode
Step 2
Then button A followed by the number 2 this disables the tamper on the siren for one hour and will give a beep to notify that it’s been disabled. Open the device and change the batteries. Then to put the tamper back on.
Step 3
Press button A and enter pincode
Step 4
Then button A followed by number 3 and you should hear a beep on the siren.
My Key Pad will not disarm the system, however it does arm correctly
Please check that your PIN is not 0000, if it is please follow the steps to change your PIN.
Can I extend my entry and exit time on my HSA 6200 Alarm Kit?
Not on this system. 20 seconds is the default for every device.