Support for HSA62000

Getting Started FAQ's

• How do I pair my siren to the hub?

  To pair the siren to the hub please follow the steps below:

  • Press and hold the learn button on the hub until the LED flashes.
  • Make sure dip switches 1 2 3 and 4 on siren are on OFF position , then turn the power switch ON and press the learn button for 1 second.
  • Go back to the hub and press the learn button for 1 second.
  • Go to the siren and press the learn button for 1 second.
  • Press and hold the learn button on the hub until the LED stops flashing.

  To test it , you will have to fully arm the system and wait for the countdown to finish. Then trigger the alarm with any door contact set to entry.

• How do I install my HSA 6200 Alarm Kit?

  How to Install Yale's HSA App-Enabled Alarm - YouTube

• How do I remove a device from my HSA 6200 Alarm?

  1. Press button A and enter pincode.
  2. Then button A followed by the number 2 this disables the tamper on the siren for one hour and will give a beep to notify that it’s been disabled. Then remove the batteries and this will remove the device from the system.
  3. To reenable the tamper press button A followed by the pincode.
  4. Then button A followed by number 3 and you should hear a beep on the siren.

• I am installing my Yale siren-based alarm, but I can’t disable the siren tamper. Why is this?

  1. Remove the front cover of the siren and turn it to off using the on/off switch.
  2. Press the learn button twice to remove the residual power.
  3. Then move switch 1 and 4 to the ON position.
  4. Then turn the power on and it will beep and flash.
  5. Switch 1,2 ,3 - to the OFF position.
  6. Switch 4 - to the ON position.
  7. To reprogram the keypad press the learn button on the siren for 1 second and you will get a beep and a flash.
  8. Press all the learn buttons on all the devices once to learn them back in again and you will hear a beep every time they are learnt back in.
  9. To learn the keypad back in press button A and add pincode.
  10. Then button A and the number 8.
  11. Then button A and number 1, then press disarm twice and press the learn button on the siren. Now disable the tamper then fit the siren back on the wall .

• How do I add devices to my HSA 6200 alarm?

  1. Press button A followed by pincode.
  2. Then button A followed by number 2.
  3. Press button A and then number 4 and the siren will beep and flash at this point. Now you can press the button on the device you want to add and the siren will beep and flash.
  4. Then press button A and the number 5.
  5. Now press button A and the number 3. Then press disarm twice.

• There are no lights on my Door Contact / Keypad after I have changed the batteries

  Go into your programme menu (blue menu button, then enter your pin code followed by the tick key), to prevent an alarm activation. Then continue to change the batteries.

• What positions do the DIP switches need to be?

  • 1,2,3 – OFF
  • 4 – ON

• Can I ‘part arm’ my system, using the HOME button on the keypad?

  This feature is not available for this system.

• Can I extend my entry and exit time on my HSA 6200 Alarm Kit?

  Not on this system. 20 seconds is the default for every device.

• Can I have an internal sounder on the HSA 6200 Alarm Kit?

  Yes, you can purchase a HSA 6400 panel, as an additional item, to give you this feature.

• How do I change the batteries on my HSA 6200 alarm?

  1. Press button A and enter pincode
  2. Then button A followed by the number 2 this disables the tamper on the siren for one hour and will give a beep to notify that it’s been disabled. Open the device and change the batteries. Then to put the tamper back on.
  3. Press button A and enter pincode
  4. Then button A followed by number 3 and you should hear a beep on the siren.